The plate gives a finished look and is necessary when mounting through a soft surface, such as carpet. This Radium bulkhead plate kit is great when multiple -6AN bulkhead fittings need to pass through a wall, floor, etc. Installation instructions including wiring diagrams Crimpless Solder Heat Shrink Butt Connectors (x4).Quick-Connect Posi-Tap “TRIGGER” Connector (x1).Weatherproof Mini Fuse Flying Lead Connector (x1).Weatherproof Mini Fuse Holder with Mounting Tab (x1).Weatherproof Relay Flying 12” Lead Connector (x1).Weatherproof SPDT 12V/40A Relay with Mounting Tab (x1).If a Radium Triple Pump MPFST was purchased, select “Quantity: 3”. If a Radium Dual Vertical Bosch 044 FST was purchased, select “Quantity: 2”. If a Radium Single Internal Pump FST was purchased, select “Quantity: 1”. For this reason, order a wiring kit for EACH fuel surge tank pump. Radium recommends a dedicated fuse and relay for each fuel surge tank pump. Necessary ring terminals are included for connecting to an external Bosch 044 fuel pump as well. Crimpless solder-based butt connectors make reliable wire connections easy and clean. Aircraft grade TXL wiring is resistant to all chemicals and elevated temperatures. The relay and fuse holder are sealed to allow installation in weather exposed areas if necessary. It uses the highest quality components to ensure proper operation in all conditions. This Do-It-Yourself wiring kit includes the necessary parts to construct a power wiring harness for one fuel surge tank pump. All wiring lead ends are labeled for ease of installation. The high temperature braided sleeving is flame retardant and is rated for over 250 Fahrenheit. These leads both use 5/16” ring terminals. The other two connections for this harness are 12V power and chassis ground. Fuel surge tanks typically use the main fuel pump’s relay trigger from the ECU. Also included is a environmentally sealed relay that has a mounting boss as well.įor wiring, all that is required is a source for the FST fuel pump(s) trigger signal. Note: a higher current fuse may be required if fuel pressure is run excessively high. The harness includes a environmentally sealed mini fuse holder that has an integrated mounting boss.

This fully assembled universal wiring harness is designed to work for the following Radium Engineering fuel surge tanks: However, they can be used in any application using a 3/4”-16 O-ring port which is the same thread pitch used in -8AN fittings. These adapter fittings are designed to be used in many Radium products including fuel rails, surge tanks, fuel pressure regulators, etc. Replacement FST Perimeter O-rings (x16)ĭetermine if a pump needs to be included and select which Walbro version will be used.Stainless Steel Pinch Clamp, Factory Crimped.Billet Aluminum Bulkhead Fitting with O-ring.Internal Bulkhead Wiring for Walbro (specify which pump).Walbro 400 specific Laser Cut Mounting Bracket.Walbro 400 specific Billet Aluminum Bottom Cap.The following parts will be reused: billet FST canister, billet FST top cap, three -6AN port fittings, -6AN bulkhead nut, 16 perimeter M5 bolts, 2 internal M5 bolts, external wiring harness, external mounting bracket and hardware This kit is only compatible when the original FST used one of the following pumps: Walbro GSS342 255lph, AEM 50-1000 Gas, AEM 50-1200 E85, Aeromotive 11142 or a Deatschwerks. This kit enables a Radium FST to be converted to use a single Walbro F90000262 Gas or Walbro F90000267 E85 fuel pump. This bracket is made from laser cut aluminum and powder coated black.ĬONVERSION KIT FOR WALBRO F90000262 GAS AND F90000267 E85 PUMPS It can be mounted on a floor and against a wall. This assumes the bracket is mounted to an electrically conductive material such as a steel frame.Īngled Mount – This mounting bracket is used for vehicles that may have a limited mounting height. It is not only nickel plated to resist corrosion, it also allows for components to be grounded to the spare hole in the bracket. It should also be mounted away from common collision areas.įloor and Wall Mount – This bracket is laser cut from aluminum and powder coated black and can be mounted on the side or bottom of the surge tank.įrame Mount – Because this bracket has a 90deg formed bend and is cantilevered, it is constructed from steel for superior strength. Mounting locations near heat sources or moving parts such as suspension components should be avoided. The fuel surge tank can be mounted near the main fuel tank or in the engine bay.

Radium gas tank